ENGINE
all figures are for Australian delivered 2000s fitted with Mikuni Solex carbs
Model - U-20
Manufacturer - Nissan
Classification - Gasoline
Construction - Cast Iron Block and Alloy Head
Cooling system - Water forced circulation
No. of cyl. and arrangement - 4 in line
Cycle - 4
No. of Main Bearings - 5
Combustion chamber - Wedge type
Valve arrangement - Overhead Cam
Bore x Stroke - 87.2 x 83mm (3.433 x 3.267in.)
Displacement - 1.982 litre (120.92 cu.in.)
Compression ratio - 9.5 to 1
Comp. pressure - 11.7kg/cm2 @ 350rpm (163.1 lb in2)
Max. power - 150bhp @ 6000 rpm
Max. torque - 19.1m-kg @ 4800 (138 ft.lb. @ 4800)
Engine idle speed - 700 rpm
Lenght x Width x Height - 692 x 641 x 670mm
Weight - 160 kg  (353 lb.)
Firing order - 1-3-4-2
Piston material - LO-EX
Number of rings - 2 compression, 1 oil
Valve timing - intake open 30deg. BTDC
                   - intake close 70deg. ATDC
                   - exhaust open 70deg. BTDC
                   - exhaust close 30deg. ATDC

VALVE MECHANISM
Valve Clearance (Hot) - In. 0.2 mm (0.0079 in.)
                                    - Ex. 0.3 mm (0.0118 in.)
Wear Limit of Dittoed Clearance - 0.35 mm (0.0138 in.)
Valve Head Dia.          - Intake 46 mm (1.81 in.)
                                   - Exhaust 36 mm (1.42 in.)
Valve Stem Dia.          - Intake 8.7 mm (0.343 -0.0012 in.)
Valve Stem Dia.          - Exhaust 8.7 mm (0.343 in.)
Valve Length              - Intake 120.8 mm (4.76 in.)
                                   - Exhaust 120.8 mm (4.76 in.)
Valve Lift                     Solex 11.6 mm (0.46 in.)
                                     SU 11.2 mm (0.44 in.)
Valve Spring Free Length - Outer 49.7 mm (1.96 in.)
                                         - Inner 48.4 mm (1.91 in.)
Valve Spring Loaded Length -Outer 29.6 mm/76.4kg (l.l7 in./168.1lb.)
                                             - Inner 27.6 mm/29.9kg (1.09 in. /65.8lb.)
Valve Spring Assembled Height Outer 41.2 mm/32.3 kg (1.62 ih./71. 1 lb.)
                                                - Inner . 39.2 mm/13.3 I~g (1.54 in./29.3 lb.)
Valve Spring Effective Turns - Outer 4.25
                                             - Inner 5.5
Valve Spring Wire Dia. - Outer 4.6 mm (0.18 in.)
                                     - Inner 2.95 mm (0.116 in.)
Valve Spring Coil Dia. - Intake 35.0 mm (1.38 in.)
                                    - Exhaust 24.2mm (0.95in.)
Valve Guide Length     - Intake 55.0 mm (2.17 in.)
                                    - Exhaust 55.0 mm (2.17 in.)
Valve Guide Height From Head Surface 13.0 + 0.1 mm (0.512 + 0.004 in.)
Valve Guide Inner Dia. - Intake 8.685 8.700 mm (0.3419 0.3425 in.)
                                     - Exhaust 8.6858.700 mm (0.34190.3425 in.)
Valve Guide Outer Dia. - Intake 14.313 14.326 mm (0.56350.5640 in.)
                                     - Exhaust 14.31314.326 mm (0.56350.5640 in.)
Valve Guide to Stem Clearance - Intake 0.015 0.043 mm (0.0006 0.00]7 in.)
                                                 - Exhaust 0.045~0.073 mm (0.00180.0029 in.)
Valve Seat Width         - Intake 1.40 mm (0.055 in.)
                                    - Exhaust 1.77 mm (0.069 in.)
Valve Seat Angle         - Intake 45deg
                                   - Exhaust 45deg
Valve Seat Interference Fit  - Intake 0.081 0.113 mm (0.0032 0.0044 in.)
                                           - Exhaust 0.0640.096 mm (0.00250.0038 in.)
Valve Guide Interference Fit - Intake 0.022 0.050 mm (0.00090.0020 in.)
                                             - Exhaust 0.0220.050 mm (0.00090.0020 in.)
CAMSHAFT AND TIMING CHAIN
Camshaft End Play         0.1 ~ 0.3 mm (0.0039 0.0118 in.)
Camshaft Lobe Lift       solex 8.3 mm (0.327 in.)
                                          SU 8.0 mm (0.315 in.)
Camshaft Journal Dia. - 1st 29.964 ~ 29.977 mm   (1.1800 ~ 1.1802 in.)
                                    - 2nd 29.964 ~ 29.977 mm  (1.1800 ~ 1.1802 in.)
                                    - 3rd 29.964 ~ 29.977 mm  (1.1800 ~ 1.1802 in.)
                                    - 4th 29.964 ~ 29.977 mm  (1.1800 ~ 1.1802 in.)
                                    - 5th 24.966 ~ 24.979 mm  (0.9830 ~ 0.9834 in.)
Camshaft Bend  (Measure Center journal with Both end journals supported)
                                          less than 0.01 mm (0.0004 in.)
Camshaft Journal to Bearing 
                   No.1 to 4    0.023 ~ 0.052 mm (0.0009 ~ 0.0020 in.)
          Clearance No.5   0.0210.047 mm (0.0008~0.0019 in.)
Camshaft Bearing Inner Dia.       - 1st  30mm +/- 0.016  (1.18 in. +/- 0.0006)
                                                    - 2nd 30 mm +/- 0.016  (1.18 in. +/- 0.0006)
                                                    - 3rd 30mm +/- 0.016   (1.18 in. +/- 0.0006)
                                                    - 4th 30 mm +/- 0.016  (1.18 in. +/- 0.0006)
                                                    - 5th 25mm +/- 0.013   (0.98 in. +/- 0.0005)
Rocker Arm Lever Ratio         Approximately 1.4: 1

CONNECTING ROD
Center Distance                        144 +/- 0.03 mm (5.67_/-  0.001 in.)
Bearing Length                         24 +/- 0.1 mm (0.94 +/- 0.0039 in.)
Bearing Thickness STD          1.493 1.506 mm (0.0588 0.0593 in.)
Big End End Play                     0.2~0.3 mm (0.008~0.012 in.)
Connecting Rod Bearing Clearance     0.0340.086 mm (0.0013 0.0034 in.)
Connecting Rod Bend              Less than 0.04 mm per 100 mm length (0.0016 in.per 3.94 in.)

CRANKSHAFT AND MAIN BEARING
Journal Dia                                2.942 62.955 mm (2.4780 2.4785 in.)
Journal Taper & Out-of-Round            Less than 0. 005 mm (0.0002 in.)
Crankshaft Free End Play       0.05 0.18 mm (0.0020.007 in.)
Wear Limit of Dittoed Play     0.3 mm (0.012 in.)
Crank Pin Dia                            51.941 - 51.954 mm (2.0449 - 2.0454 in.)
Crank Pin Taper& Out-of-Round         Less than 0.005 mm (0.002 in.)
Main Bearing Thickness STD             1.822 - 1.835 mm (0.0717 - 0.0722 in.)
Main Bearing Clearance                       0.020 - 0.072 mm (0.0008 - 0.0028 in.)
Wear Limit of Dittoed Clearance        0.12 mm (0.0047 in.)
Crankshaft Bend                                   Less than 0.03 mm (0.0012 in.)

JACKSHAFT
Journal Dia.               - 1st 45.434~45.447 mm  (l.7887~1.7892 in)
                                    - 2nd 43.877~43.910 mm  (1.7274- 1.7287 in.)
                                    - 3rd 41.218~41.231 mm   (1.62281.6233 [n.)
Jackshaft Free End Play        0.08 0.28 mm (0.0031 0.0110 in.)

PISTON
Piston Dia.                 - STD 87.180 87.230 mm (3.4323 3.4342 in.)
                                    - Oversize 1 87.410 87.460 mm (3.4413 3.4433 in.)
                                    - Oversize 2 87.660~87.710 mm (3.4512~3.4531 in.)
                                    - Oversize 3 87.910 87.960 mm (3.4610 3.4630 in.)
                                    - Oversize 4 88.160~88.210 mm (3.4709~3.4728 in.)
                                    - Oversize 5 88.660 88.710 mm (3.49053.4925 in.)
Ellipse Difference       0.39 ~ 0.42 mm (0.0154~0.0165 in.)
Ring Groove Width - Top 2.0 mm  (0.079 in.)
                                    - Second 2.0 mm (0.079 in.)
                                    - Oil 4 mm (0.157 in.)
Piston to Bore Clearance     0.0300.050 mm (0.0012 0.0020 in.)
Piston Pin Hole Off-Set       1 +/-  0.05 mm (0.03937 +/- 0.0020 in.)

PISTON PIN
Pin Dia                                          22 mm (0.866 in.)
Pin Length                                    72.6 mm (2.858 in.)
Piston Pin to Piston Clearance      0.006 0.012 mm (0.0002 0.0005 in.)
Piston Pinto Connecting Rod Bushing Clearance 
                                                     0.0250.035 mm (0.0010 0.0014 in.)
PISTON RING
Piston ring height 
       - top & 2nd compression ring - 2mm (0.079in.)
                          - oil ring - 4.0mm (0.1575in.)
Ring side clearence  - top compression ring 
                          - 0.04-0.073mm (0.0016-0.0029in.) 
                                 - 2nd compression ring 
                          - 0.03-0.063mm (0.0012-0.0025in.)
                                 - oil ring
                          - 0.025-0.063mm (0.001-0.0025in.)
Ring gap width         - top compression ring 
                          - 0.25-0.4mm (0.01-0.016in.)
                                 - 2nd compression ring 
                          - 0.15-0.3mm (0.006-0.012in.)
                                 - oil ring 
                          - 0.14-0.29mm (0.0055-0.0114in.)

CYLINDER BLOCK
Cylinder bore out-of-round tollerance 
                          - <0.015mm (<0.0006in.)
Cylinder bore taper - 0.02mm (0.0008in.)
Cylinder head surface flatness - <0.1mm (<0.004in.)

IGNITION SYSTEM
Starting method - magnetic starting system
Ignition method - battery coil type
Ignition timing - 20deg. BTDC at 700rpm
Firing order - 1 - 3 - 4 - 2
Ignition coil - Hitachi C6R-50 or
                   - Hanshin HV-13Y
Coil primary voltage - 12 volts
Coil required current - engine stopped - 3.5 amp.
                                - engine running - 2.15 amp.
Coil resistance - primary 1.4 ohm. - secondary 14 K/ohm.
Distributor - Hitachi D407-51
Ignition timing advance system - governor
Advance starting speed - 800-1100 rpm
Rotating direction - left
Points gap - 0.45-0.55mm (0.0177-0.0217in.)
Dwell angle - Hitachi - 49-55 deg.
Contact arm spring tension - 0.5-0.65 kg (1.1-1.43lb.)
Condenser capacity - 0.20-0.24 uF
Spark plug - Nihon Tokushu Togyo (NGK) B-6E
                   - Hitachi L-45
Spark plug size - screw diameter x reach 
                   - 14 x 19mm (0.551 x 0.75 in.)
Spark plug gap - 0.7 - 0.8 mm (0.027 - 0.031 in.)
Spark plug torque - 1.5-2.0kg/m (11.0-15.0 ft/lb.)

FUEL SYSTEM
Carburetor - Mikuni 44PHH
Type - dual throat side draught
Throttle bore - 44 mm (1.496 in.)
Venturi Size - Outer 37 (1.456)
                    - Inner 10 (0.3937)
Main Jet - #180
Pilot Jet - #60
Pump Jet - 0.3mm (0.01181in.)
Air cleaner - paper type, Tsuchiya brand
Fuel pump - diaphragm type
Diaphragm spring free length 
                       - Showa Seiki - 52-54mm (2.05-2.13in.)
                       - Kyosan Denki - 57-59mm (2.24-2.32in.)
Diaphragm spring pressured length 
  - Showa Seiki - 22mm/3.9-4.3kg (0.87in./8.58-9.46lb.)
  - Kyosan Denki - 14mm/4.2-4.6kg (0.71in./9.24-10.12lb.)
Rocker arm spring free length 
                       - Showa Seiki - 24-24.5mm (0.94-0.96in.)
                       - Kyosan Denki - 31mm (1.22in.)
Discharge pressure 
                       - Showa Seiki - <220mm/Hg (8.66in.Hg)
                       - Kyosan Denki - <220mm/Hg (8.66in.Hg)
Suction vacuum - Showa Seiki - >300mm/Hg (11.8in./Hg)
                       - Kyosan Denki - >400mm/Hg (15.75in./Hg)
Fuel tank capacity - 43 litre (11.36 US gal.)

LUBRICATING SYSTEM
Method - forced pressure type
Oil pump type - gear type
Oil filter - full flow type
Oil pan capacity - 7.1 litre (1.875 US gal.)
Oil pressure measured while hot at 700rpm
                              - 1.0 kg/cm2 (14.9 lb/in2)
Relief valve spring free length - 62.3mm (2.453in.)
Relief valve spring pressured length 
                              - 40mm/8.13kg (1.575in./17.89lb.)
Opening pressure - 4.5kg/cm2 (63.9lb/in.2)
Gear side clearence - 0.04-0.11mm (0.002-0.0043in.)
Gear backlash - 0.3-0.4mm (0.01-0.02in.)

COOLING SYSTEM
System type - water cooling closed type
Radiator - corrugated fin and tube type
Type - Nihon Radiator
System capacity - 8.5 litre (2.11 US gal.)
Water pump - centrifugal type
Pump vane to body clearence 
                                 - 0.7-0.9mm (0.028-0.035in.)
Cooling fan diameter - 350mm (13.78in.)
Fan belt deflection - 15-20mm (0.59-0.79in.)
Thermostat - pellet type
Thermostat opening temperature 
                                 - 76.5 deg.C (169.7 deg.F)
Thermostat valve lift 
                   - 8mm at 95 deg.C (0.31in. at 203 deg.F)

BATTERY
Type - 12 volt , 50 AH
Battery manufacturers - Yuasa , Furukawa , GS .
Polarity - negative earth

ALTERNATOR
Type - Mitsubishi AS2030A2
Generating method - alternator
Voltage - 12 volt
Capacity - 30 amp.
Pulley ratio - 1.73
Shaft bend limit - 0.1mm (0.004in.)
Brush height - 12.0mm (0.472in.)
Brush limit height - 5.0mm (0.179in.)

VOLTAGE REGULATOR
Type - Mitsubishi RL-2220B5
Load adjust voltage - 13.5-14.5 volts
Air gap - 0.8-1.2mm (0.315-0.472in.)
Back gap - 0.8-1.1mm (0.315-0.433in.)
Point gap - 0.3-0.4mm (0.118-0.157in.)

STARTER
Type - Mitsubishi ME-Y2R
Power - 12 volt  1.4 hp
Stall torque - >1.0kg/m (>7.2 ft/lb.)
Pinion gear - number of teeth - 9
Commutator diameter - 39mm (1.54in.)
Commutator diameter wear limit - 2mm (0.08in.)
Brush length - 17mm (0.67in.)
Brush length wear limit - 6.5mm (0.26in.)
Shaft to bearing clearence 
                               - 0.05-0.1mm (0.002-0.0039in.)
Amendment limit - 0.2mm (0.008in.)

CLUTCH
Type - single dry disc hydraulic operation
Number of plates - 2 (facing)
Clutch Material - Textar
Clutch spring type - diaphragm spring
Number of springs - 1
Number of torsion springs - 6
Outer diameter x inner diameter x thickness 
                  - 200 x 130 x 3.5 mm (7.87 x 5.12 x 0.138 in.)
Total friction area - 363mm (56.12in.)
Clutch pedal free travel - 10-20mm (0.39-0.79in.)
Clutch pedal height - 167mm (6.57in.)
Disc run out - 0.5mm (0.0197in.)
Release lever or diaphragm spring height from flywheel 
        face - 43.5mm (1.71in.)
Release lever run out - 0.8mm (0.032in.)
Withdrawal lever play - 2.5mm (0.098)
Out of balance of clutch - 12.0mm (0.47in.)
Backlash at splined part - 0.08-0.12mm (0.003-0.005in.)
Disc assembly thickness 
                       - free - 8.3-9.4mm (0.327-0.37in.)
                       - bending - 1.0-1.3mm (0.039-0.051in.)
                       - compressed - 7.3-8.1mm (0.287-0.319in.)

TRANSMISSION
Model - FS5C71A
Type - 5 forward, 1 reverse.
           Synchromesh on 1st, 2nd, 3rd, 4th and 5th.
Synchro type - servo type
Operating method - floor shift
Gearbox oil pan capacity - 2.6 litre (0.68 US gal.)
Ratios - 1st - 2.957
            - 2nd - 1.858
            - 3rd - 1.311
            - 4th - 1.000
            - 5th - 0.852
            - reverse - 3.365
Number of teeth - main shaft - main drive gear - 23
                                           - 3rd gear - 28
                                           - 2nd gear - 29
                                           - low gear - 34
                                           - reverse gear - 36
                                           - overdrive - 21
                    - counter shaft - counter driven gear - 28
                                           - 3rd gear - 26
                                           - 2nd gear - 19
                                           - low gear - 14
                                           - reverse gear - 15
                                           - overdrive - 30
                      - reverse idler gear - 17
                      - speedometer - drive gear - 6
                                            - driven gear - 18
Adjustments 
 - ammendment limit of main shaft end play 
                                    - 0.4mm (0.0157in.)
 - counter shaft end play 
                                    - 0-0.10mm (0.002-0.0059in.)
  - main shaft end play 
                           - 0-0.35mm (0-0.0138in.)
  - ammendment limit of counter shaft end play 
                           - 0.2mm (0.0079in.)
  - reverse idler gear end play 
                           - 0.05-0.35mm (0.002-0.0138in.)
  - ammendment limit of reverse idler gear end play 
                           - 0.4mm (0.0157in.)
  - main drive adjust washers 
                           - 2.0mm (0.08in.)
                           - 2.1mm (0.082in.)
                           - 2.2mm (0.09in.)
  - counter shaft adjust washers 
                           - 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1.0mm
                           - (0.016, 0.02, 0.024, 0.028, 0.031, 0.035, 0.039in.)
Backlash between gears - 1st, 2nd, 3rd, 4th & 5th 
                           - 0.05-0.1mm (0.002-0.004in.)
                           - reverse - 0.1-0.15mm (0.0039-0.0059in.)
                           - speedometer gear - 0.2mm (0.0079in.)

PROPELLER SHAFT
Length x outer diameter x inner diameter
          838 x 63.5 x 60.3 mm (32.99 x 2.5 x 2.374 in.)
Universal joint - Spicer type
Universal joint journal outer diameter 
                             - 14.8mm (0.58in.)
Bearing race inner diameter - 18.8mm (0.74in.)
Number of needle roller bearing - 26
Needle bearing outer diameter - 2.0mm (0.079in.)
Joint size - 63H
Adjustments 
 - sleeve yolk spline backlash 
                   - 0.024-0.066mm (0.0009-0.0026in.)
 - snap ring thickness for needle roller cap 
                   - 2.0mm (0.079in.)
 - spider thrust play 
                   - 0.02mm (0.0008in.)
 - propeller shaft run out 
                   - 0.6mm (0.024in.)
 - dynamic balance 
                   - 15gram/4000 rpm (0.529oz./4000 rpm)

FINAL DRIVE
Type of gear - hypoid
Gear ratio - 3.7
Housing type - banjo
Differential gear oil capacity - 0.93 litre (0.25 US gal.)
Type and number of gears 
                         - straight bevel pinion - 2 of each
Number of teeth - drive pinion - 10
                           - ring gear - 37
                           - pinion mate - 10
                           - side gear - 18
Adjustment 
  - preload for pinion bearing 
                           - 10-13kg/cm (8.7-11.3lb/in.)
  - pinion height - 61.0mm (2.4in.)
 - drive pinion bearing adjusting shims 
                            - 3.8-3.82mm (0.149-0.15in.)
 - drive pinion adjusting shims 
                            - 0.5, 0.25, 0.125, 0.075 & 0.05mm
                            - (0.02, 0.01, 0.005, 0.003 & 0.002in.)
 - side gear to case clearence 
                            - 0.1-0.2mm (0.004-0.008in.)
 - ammendment limit of side gear to case clearence 
                            - 0.3mm (0.012in.)
 - side bearing adjusting shims 
                            - 0.5, 0.25, 0.125, 0.075 & 0.05mm
                            - (0.02, 0.01, 0.005, 0.003 & 0.002in.)
 - side gear thrust washer sizes 
                            - 0.76-0.81, 0.86-0.91, 0.96-1.01, 
                              1.06-1.11 & 1.16-1.21mm
                            - (5.49-5.86, 6.22-6.58, 6.94-7.3, 
                              7.66-8.03 & 8.39-8.75in.)
 - pinion mate thrust washer 
                            - 0.76-0.81mm (0.03-0.032in.)
 - maximum run out of ring gear 
                            - <0.05mm (<0.002in.)
 - backlash between side gear and pinion mate 
                            - 0.02-0.08mm  (0.0008-0.0032in.)
  - backlash between ring gear & pinion 
                            - 0.15-0.2mm (0.006-0.008in.)
Rear axle adjustment 
  - shaft end play - <0.51mm (<0.0020in.)
  - adjusting shims - 0.075mm (0.0030in.)

STEERING SYSTEM
Type - cam and lever
Gear ratio - 14.8
Steering box oil capacity - 0.25 litre (0.07 US gal.)
Steering angle in - 36deg.16'  -  out - 28deg.20'
Steering wheel diameter - 400 mm (15.75 in.)
Number of turns lock to lock - 2.7
Turning force at steering column - 0.3-0.8kg (0.7-1.8lb.)
Adjustment 
  - steering wheel play 
                          - 25-30mm (0.98-1.18in.)
  - backlash between worm and pin 
                          - <0.2mm (<0.008in.)
  - axial play and radial play between nut and ball 
                          - 0.08mm (0.0031in.)
  - worm bearing preload 
                          - 8-15kg/m (0.31-0.59lb/in.)
  - worm bearing interference fit 
                          - <0.01mm (<0.0004in.)
  - worm adjusting shim sizes 
                          - 0.762, 0.254, 0.127 & 0.05mm
                          - (0.03, 0.01, 0.005 & 0.002in.)
  - sector shaft shims 
                          - 1.45mm & 1.57mm (0.0571 & 0.0618)
  - standard shim thickness - 2.5mm (0.10in.)
  - shaft to bush clearence 
                          - 0.017-0.06mm (0.0007-0.0024in.)
  - shaft adjusting shim 
                          - 3.2mm (0.13in.)
  - off-set at centre of worm and pin 
                                          - 4.7mm (0.19in.)

BRAKING SYSTEM
Front brakes - Sumitomo twin piston calipers made 
                        under licence from Dunlop
Front brake pad dimensions 
       - 47.5 x 16.7 x 53.98 mm (1.87 x 0.66 x 2.125 in.)
Front brake total braking area - 102.6cm2 (15.9 in.2)
Diameter of front disc - 284 mm (11.18 in.)
Front caliper inner diameter - 53.98mm (2.125in.)
Rear brakes - alloy finned drum brakes with one leading and one 
                       trailing shoe
Rear brake shoe dimensions 
                   - 40 x 4.5 x 215 mm (1.57 x 0.18 x 8.46 in.)
Rear brake total braking area - 351cm2 (54.4 in.2)
Diameter of rear drum - 228.6 mm (9.0 in.)
Rear wheel cylinder inner diameter - 20.64mm (0.8in.)
Master cylinder - 19.05mm (0.75in.)
Adjustment 
    - rotor run out - <0.08mm (<0.003in.)
    - drum out of round - <0.02mm (<0.0008in.)
    - front pad wear limit - 5.3mm (0.21in.)
    - rear shoe lining limit - 0.5-1mm (0.012-0.039in.)
    - front pad to rotor clearence 
                                    - 0.18-0.31mm (0.007-0.012in.)
    - rear shoe to drum clearence - 0.25mm (0.01in.)
    - brake pedal free travel - 10-15mm (0.39-0.59in.)
    - brake pedal height - 167mm (6.57in.)
Wheel cylinder - rear 20.64mm (0.813in.)
Max. fluid pressure - 137 kg/cm2
Park brake - mechanical type on rear wheel

SUSPENSION
Front - independent coil spring
Front coil spring size - 12.7 x 87.5 x 290 mm - 6 turns
Coil spring wire diameter - 12.7mm (0.5in.)
Coil spring diameter - 87.5mm (3.44in.)
Coil spring free length - 290mm (11.42in.)
Spring constant - 9.5kg/mm (522.5lb/in.)
Front shock absorbers - telescopic double acting
Shock absorber damping force 
                 - rebound - 190kg (418lb.)
                 - compression - 70kg (154lb.)
Stroke - 110mm (4.3in.)
Maximum length - 310mm (12.2in.)
Minimum length - 200mm (7.9in.)
Stabilizer - front - torsion bar type
Adjustments 
  - wheel bearing preload - <15.0kg/cm (<13.0lb/in.)
  - wheel bearing axial play - <0.08mm (<0.003in.)
  - camber adjusting shim sizes - 1mm & 2mm 
                                                      (0.04in. & 0.08in.)
Rear - parallel semi elliptic leaf springs
Rear spring size 
  - 1200 x 60 x 6 - 2 (47.2 x 2.4 x 0.24 - 2)
                         5 - 2                     (0.2 - 2)
Free camber - 66.5mm (2.62in.)
Laden camber - neg.6.0mm/185kg (neg.0.24in./407lb.)
Bush pin diameter - 12.0mm (0.47in.)
Leaf spring adjustment 
   - bush to pin clearence - <0.113mm (<0.0044in.)
Rear shock absorbers - telescopic double acting
Shock absorber damping force 
  - rebound - 120kg (264lb.)
  - compression - 30kg (66lb.)
Stroke - 162mm (6.4in.)
Maximum length - 414mm (16.3in.)
Minumum length - 252mm (9.9in.)

WHEEL ALIGNMENT
These figures quoted are the factory specs for cars fitted with the original cross ply tyres, the figures may not be appropriate for cars fitted with radial tyres.
Caster (unladen) - 1o30'
Camber (unladen) - 1o25'
Toe-in (unladen) - 2.0-3.0mm (0.08-0.12in.)
Inclination angle of axle (unladen) - 6o35'
Turning angle of front wheel - inside - 36o16'
                                           - outside - 28o20'

FRAME
Type - X member 
Section - box type
Height x width x thickness
    Upper 75 x 100 x 1.6 mm
    Lower 25 x 100 x 2.3 mm
Weight - 505kg (1091.2lb.)